Process Pumps

These Air Cooled Thermic Fluid series of process pumps come with a back pull out design, which enables to remove the rotating unit of pump for inspection and repairs without disturbing suction and delivery pipe connections. 

SPECIFICATIONS 

• Delivery size from 32 mm to 80 mm

• Capacity up to 250 m3/hr

• Head up to 100 metres

• Working pressure up to 16 bar

• Temperature up to 350° C

APPLICATIONS 

• Thermic fluid

• Synthetic oil

• Hot oil

These process pumps are used for handling various types of CLEAR & CLEAN chemical liquids with leak-free transportation. These pumps are manufactured to close tolerance and are of rigid construction. These pump is a magnetic drive pump. 

SPECIFICATIONS 

• Delivery size up to 100 mm

• Capacity up to 300 m3/hr

• Head up to 150 metres

• Speed 2900, 1450, 980 rpm at 50 Hz and 3500, 1750, 1150 rpm at 60 Hz.

• Temperature from (-)50° to 180° C

APPLICATIONS 

• Chemicals - paints, solvents, intermediaries, resin, polymers and other acidic and basic chemicals

• Pharmaceuticals

• Petrochemicals

• Suitable for various process industries for clean/clear liquids without any suspended particles

These pumps are used for handling various types of chemical liquids. These pumps are manufactured to close tolerance and are of rigid construction. These pumps are mainly used in process industries. The complete range of process pumps is covered by four driving units, thereby reducing inventory and achieving interchangeability. 

SPECIFICATIONS 

• Delivery size up to 150 mm

• Capacity up to 500 m3/hr

• Head up to 150 metres

• Working pressure 16 - 25 bar

• Temperature up to 180° C

APPLICATIONS 

• Acids/alkalis

• Hydrocarbons, oils

• Various process chemicals

• Food processing units

These End Section Process Pump are horizontal, radially split, single stage, centrifugal end-suction volute with top centerline delivery. The impeller is of an enclosed type. The bearing housing is fitted with a support foot. The pump shaft is supported by pre-lubricated anti-friction sealed bearings as a standard scope of supply. These pumps come without mechanical seal & without gland packing arrangement and yet ensure zero leakage from the stuffing box. This feature is achieved by the innovative design of the shaft sleeve, expeller and fluid arrester. 

SPECIFICATIONS 

1. At 1450 rpm

   • Rate of flow up to 180 m3/hr

   • Head up to 55 m

2. At 2900 rpm

   • Rate of flow up to 150 m3/hr

   • Head up to 85 m

   • Temperature – up to 95 °C

APPLICATIONS 

• Light chemicals like caustic soda, weak acids, etc.

• Food & beverage industries – (sugar, vegetable oils, etc.)

• Other applications like hot water, brine, DM water, lime water, etc.

These process pumps are mainly used for chemical and process handling applications, which are free from suspended solids particles. These process pumps are ideal for pumping corrosive and noxious fluids. 

SPECIFICATIONS 

• Delivery size ranging from 32 to 50 mm

• Capacity ranging from 4 to 80 m3/hr

• Head up to 60 metres

• Working pressure 16 bar

• Temperature up to 90° C

APPLICATIONS 

• Liquefied gases (e.g. ammonia, freons, carbon dioxide, amines, vinyl chloride, ethylene oxide, phosgene (>150°C), etc.

• Aggressive/toxic/explosive/hazardous/flammable chemicals (sulphuric acid, nitric acid, hydrofluoric acid, hydrocyanic acid, ethanoic acid, formic acid, etc.)

These End Section Process Pump are used for handling various types of chemical liquids. These process pumps are manufactured to close tolerance and are of rigid construction. However, proper installation, operation and maintenance are equally important to ensure trouble free service. These process pumps are either gland packed or mechanically sealed. These pumps come with an enclosed impeller (with casing cover for heating/cooling arrangement.). These pumps are equipped with a semi-open impeller while these type pumps come with a jacketed delivery, casing and casing cover. 

SPECIFICATIONS 

• Delivery size up to 350 mm

• Capacity up to 1550 m3/hr

• Head up to 225 metres

• Working pressure 16 - 25 bar

• Temperature (-) 50° C – 350° C

APPLICATIONS 

• Process industries

• Petro-chemical industry

• Nuclear industry

• Refineries, fertiliser, paper, sugar and other industries

• Air-conditioning

• Distilleries

• Water treatment plants