Elastomer Spring seals used for water and sewage containing slurries. Shaft run out is compensated by Elastomer bellow and spring due to its self aligning capability.Elastomer Bellow protect Shaft/Sleeve from Fretting. 

Pressure  : up to 15 bars

Temperature : (-)50c to (+)350c

Speed : up to 25 m/s

Size : 19 mm to 100 mm

Multi Spring Balance Seals are pusher type balance multiple spring mechanical seals generally used when high pressure sealing required.

Balanced Spring seals are compact in design suiting all types of rotating equipment’s – pumps and mixers. Drive lugs in the retainer will provide torque transmission and reduce slippage on shaft and sleeve

Pressure  : 30 bars (Max)

Temperature : (-)20c to (+)220c

Speed : 2900 rpm (Max)

Size : 12 mm to 100 mm

Multi Spring Unbalance Seals is pusher type unbalanced seals used to avoid distortion at high speeds and ensure uniform pressure on seal faces under all operating conditions and Prevents any kind of leakage.

Multi Spring unbalanced seals can be easily assemble or dismantled through circlip provided and can be change to balance version by changing only the seal ring and the secondary seal.

Pressure : 10 bars (Max)

Temperature : (-)50c to (+)280c

Speed : 25 m/s

Size : 10 mm to 150 mm

Metal Bellow Seals are widely used in high temperature and highly corrosive media and suitable for high start-up torque since the bellows unit is independent of torque transmission. 

Pressure : up to 15 bars

Temperature : (-)50c to (+)350c

Speed : up to 25 m/s

Size : 19 mm to 100 mm

Teflon Bellow Mechanical seals has been designated as Fixed & replaceable bellow face respectively.For replaceable version there is flexibility for selection of face material as per the media to be sealed, which can be easily removed & replaced. 

Pressure : up to 15 bars

Temperature: (-)50c to (+)350c

Speed: up to 25 m/s

Size: 19 mm to 100 mm

Rubber Bellow Mechanical Seals can be use regardless of direction of rotation since the driving torque is not transmitted through the coil spring. The required driving torque is through the spring and spring holder. The single coil spring will avoid effluent particle. 

Pressure : up to 15 bars

Temperature  (-)50c to (+)350c

Speed : up to 25 m/s

Size : 19 mm to 100 mm

Multi Spring Unbalance Seals is pusher type unbalanced seals used to avoid distortion at high speeds and ensure uniform pressure on seal faces under all operating conditions and Prevents any kind of leakage.

Pressure : 10 bars (Max)

Temperature : (-)50c to (+)280c

Speed : 25 m/s

Size : 10 mm to 150 mm

Multi Spring Reversed Balance Seals are external mounted multi coil spring Seals. Liquid pressure is used to close the Seal faces therefore very effective in high pressure and vacuum applications. 

Pressure : 10 bars (Max)

Temperature : (-)50c to (+)180c

Speed : 2900 rpm (Max)

Size : 10 mm to 100 mm

Capsulated Spring Seals are a cost effective version of a Balanced seal They feature the same rugged and reliable construction as the Multi spring unbalanced seals.

Pressure : 6 bars (Max)

Temperature : (-)20c to (+)100c

Speed : 2900 rpm (Max)

Size : 18 mm to 100 mm

Multi Spring Balance Seals are pusher type balance multiple spring mechanical seals generally used when high pressure sealing required.

Balanced Spring seals are compact in design suiting all types of rotating equipment’s – pumps and mixers. Drive lugs in the retainer will provide torque transmission and reduce slippage on shaft and sleeve

Pressure : 30 bars (Max)

Temperature : (-)20c to (+)220c

Speed  : 2900 rpm (Max)

Size  : 12 mm to 100 mm

Single Spring Balanced Seals especially designed to suit Slurry Media Sealing,light contamination, dirty media and clogging type application. This type also allows it to fit onto a normal shaft without any balancing step. The mechanical drive of this seal is realised by grub screw which lock onto the shaft.

Pressure : 30 bars (Max)

Temperature : (-)50c to (+)180c

Speed : 1500 rpm (Max)

Size : 10 mm to 100 mm

Conical Spring Seals is single conical spring, unbalanced seal with O-ring provided for secondary sealing.

Since the Torque transmission is done by the single coil springs the seals are dependent on the directions of rotation, which is seen from the drive end of the shaft.

Pressure : 10 bars (Max)

Temperature  : (-)20c to (+)180c

Speed : 10 m/sec

Size : 10 mm to 100 mm

Single Spring Balanced Seals especially designed to suit Slurry Media Sealing,light contamination, dirty media and clogging type application. This type also allows it to fit onto a normal shaft without any balancing step. The mechanical drive of this seal is realised by grub screw which lock onto the shaft. 

Pressure : 30 bars (Max)

Temperature : (-)50c to (+)180c

Speed  : 1500 rpm (Max)

Size  : 10 mm to 100 mm

Wave Spring Seals are internally mounted which are non-clogging. They are designed for high viscous, abrasive media and are universal application and the spare parts are interchangeable without modification.

Seal faces are easily inserted. They can be designed in which spring is isolated from pump media.Torque transmission from retainer shell to seal ring is through drive pin.

Pressure : 10 bars (Max)

Temperature : (-)20c to (+)200c

Speed : up to 2900 RPM(Max)

Size : 15 mm to 100 mm

Single Spring Unbalance Seals is unbalanced single acting helical coil spring seals independent of direction of rotation.

single Coil unbalanced seals are internally mounted and easy to install.rotary seal ring is driven by the motion transmitted by the shaft to the spring.slippages are eliminated, protecting the shaft and sleeve from fretting.

Pressure : 10 bars (Max)

Temperature : -)50c to (+)280c

Speed : 2900 rpm (Max)

Size : 16 mm to 100 mm

Single Cartridge Seals a cartridge unit specially design for slurry applications and consist single seal assembly, mating ring, gland, sleeve, etc., which is pre-assembled and preset by the manufacturer prior to installation. 

Cartridge Mechanical Seals are special purpose Multi Spring Balanced Seals designed for use in media containing abrasive or solid particles. 

Pressure : Up to 15 bars

Temperature : (-)80c to (+)180c

Speed : Up to 25 m/s

Size : 25 mm to 150 mm

Dual Cartridge Seals is a factory assembled cartridge unit specially design for slurry & viscous media.Double Cartridge Seal is a self contained unit consisting two mechanical seals in a seal chamber in any combination which can utilize a pressurized barrier fluid or a non pressurized buffer fluid. 

Pressure : Up to 15 bars

Temperature : (-)80c to (+)150c

Speed : Up to 25 m/s

Size : 25 mm to 150 mm

High Pressure Seals specifically designed to handle demanding, high torque applications. High Pressure Mechanical Seal has positive drive arrangement and sturdy construction making the seal suitable for high pressure application. Multiple spring design provides uniform face loading.

Pressure : 15 bars (Max)

Temperature : (-)50c to (+)180c

Speed : 2500 rpm (Max)

Size : 25 mm to 150 mm

Metal Bellow Cartridge Seal Has its unique Features which include

• Easy to replace individual seal-wear parts.

• Single acting Inside mounted.

• Multi spring design.

• Springs are out of product, minimizes corrosion and stress related failure.

• Dynamic elastomer moves on nonmetallic surface eliminating fretting Faces.

• Designed for optimum heat dissipation.

Pressure : 2000 kpa

Temperature : 400 C

Speed  : 0m/sec

Size : 19 mm to 100 mm

Dry Running Mixer Seals is a multiple spring externally mounted, Reverse Balanced Seal with O-ring as secondary sealing member.

Dry Running Agitator Seals are available with cartridge, non-cartridge & with bearing assembly. Dry Running Seals design eliminates the need of auxiliary equipment for cooling & lubrication that is required for mixer application. Since there is no use of barrier fluid, thus eliminates the possibility of product contamination.

Pressure  : up to 1.40 MPa

Temperature  : (-)10c to (+)150c

Speed  : up to 1 m/s

Size : 25 mm to 150 mm

Multi Spring Slurry Seal is special purpose Multi coil cartridge balanced seal designed developed for handling slurries, sludges, thick syrups and polymerizing fluids.

The springs are isolated from the fluid being sealed by dynamic O-ring, which enhances the seal life.

Pressure : up to 15 Bars

Temperature : (-)50 to 180°C

Speed : up to 25 m/s

Size  : 25 to 150mm